Specifications
|
Description
|
---|---|
Dimensions (H x W x D)
|
|
Weight (Approximate)
|
|
Electrical specifications
Specifications
|
Description
|
---|---|
Rated line voltage
|
100 to 120 V ac
|
Rated input current
|
4.5 A (at 120 V ac) to 2.2 A (at 240 V ac)
|
Rated input frequency
|
50 to 60 Hz
|
BTU rating (Maximum)
|
|
Rated steady-state power
|
|
Maximum peak power
|
|
Environmental specifications
Specifications
|
Description
|
||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
System inlet temperature (Operating)
|
10° to 35°C (50° to 95°F), at sea level with an altitude derating of 1.0°C per every 305 m (1.8°F per every 1000 ft) above sea level to a maximum of 3048 m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above 30°C (86°F).
|
||||||||||||||||||||||||||||||||||||
System inlet temperature (Non-operating)
|
-30° to +60°C (-22° to +140°F). Maximum rate of change is 20°C/hr (36°F/hr).
|
||||||||||||||||||||||||||||||||||||
Relative humidity (Operating)
|
10% to 90% relative humidity (Rh), 28°C (82.4°F) maximum wet bulb temperature, non-condensing
|
||||||||||||||||||||||||||||||||||||
Relative humidity (Non-operating)
|
5% to 95% relative humidity (Rh), 38.7°C (101.7°F) maximum wet bulb temperature, non-condensing
|
||||||||||||||||||||||||||||||||||||
Altitude (Operating)
|
3048 m (10,000 ft). Maximum allowable altitude change rate is 457 m/min (1500 ft/min)
|
||||||||||||||||||||||||||||||||||||
Altitude (Non-operating)
|
9144 m (30,000 ft). Maximum allowable altitude change rate is 457 m/min (1500 ft/min)
|
||||||||||||||||||||||||||||||||||||
Acoustic noise
|
Listed are the declared A-Weighted sound power levels (LWAd) and declared average bystander position A-Weighted sound pressure levels (LpAm) when the product is operating in a 23°C ambient environment. Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
Entry Configuration
Base Configuration
Performance Configuration
|
||||||||||||||||||||||||||||||||||||
|
HPE Smart array P420i controller specification
Specification
|
Description
|
---|---|
Dimensions
|
Embedded
|
Disk drive and enclosure
|
6 Gb/s SAS
|
Interface – transfer rate
|
6 Gb/s SATA (Serial ATA)
|
SAS connectors
|
2 internal 4X connectors
|
Cache memory speed
|
512MB FBWC – DDR3-1333 MHz with 40-bit wide bus, 1GB or 2GB FBWC DDR3-1333 MHz with 72-bit wide bus
|
Server interface
|
x8 PCIe 3.0 provides 2 GB/s maximum bandwidth
|
SAS speed
|
Eight 6 Gb/s SAS links provide 4.8 GB/s maximum bandwidth
|
Cache memory
|
|
Logical drives supported
|
|
Host memory addressing
|
64-bit, supporting greater than 4GB server memory space
|
RAID support
|
|
1. A minimum of 512MB cache is required to enable RAID 5, 50, 6, 60.
2. HPE Smart Array Advanced Pack (SAAP 2.0) is no longer required to enable RAID 6 and 60 (Advanced Data Guarding). However, controller must be in firmware version 4.68 (Or later). |
HPE Ethernet 1Gb 4-port 331FLR adapter specifications
Specifications
|
Description
|
---|---|
HPE flexible network technology
|
HPE FlexibleNet technology consists of replaceable network solutions to meet the users require now or in the future.1
|
Network interface
|
10Base-T/100Base-TX/1000Base-TX
|
Compatibility
|
|
Data transfer method
|
PCI express, four lanes (x4)
|
Chipset
|
BCM5719
|
Network transfer rate
|
|
Connector
|
Two RJ-45
|
Cable support
|
|
Reviews
There are no reviews yet.